Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing
The Alumix 13 (wt.%) (Al-4.5 Cu 0.5 Mg 0.2 Si) powder with and without 5 wt.% Saffil short fibers specimens were hot pressed in the range 580-620. °C. The densification during pressure increase was fitted using the Konopicky model and an agreement with the associated linear plot P vs. ln(1/(1 - D) w...
Guardado en:
| Autores principales: | , |
|---|---|
| Formato: | JOUR |
| Materias: | |
| Acceso en línea: | http://hdl.handle.net/20.500.12110/paper_00325910_v245_n_p13_Moreno |
| Aporte de: |
| id |
todo:paper_00325910_v245_n_p13_Moreno |
|---|---|
| record_format |
dspace |
| spelling |
todo:paper_00325910_v245_n_p13_Moreno2023-10-03T14:45:17Z Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing Moreno, M.F. González Oliver, C.J.R. Ceramic short fibers Hot pressing Liquid phase sintering Metal matrix composites Power Law Creep Super plastic deformation Hot pressing pressure Hot-pressed composites Metal matrix composites Newtonian viscous flow Power law creep Power-law creep model Short Fiber Transient liquid phase Aluminum Creep Densification Fibers Hot pressing Liquid phase sintering Metallic matrix composites Porous materials Reinforced plastics Liquids aluminum aluminum derivative copper saffil silicon unclassified drug article chemical parameters composite material controlled study deformation density flow Konopicky model liquid phase densification mathematical model physical parameters powder Power Law Creep model pressure solid stress strain relationship temperature viscosity The Alumix 13 (wt.%) (Al-4.5 Cu 0.5 Mg 0.2 Si) powder with and without 5 wt.% Saffil short fibers specimens were hot pressed in the range 580-620. °C. The densification during pressure increase was fitted using the Konopicky model and an agreement with the associated linear plot P vs. ln(1/(1 - D) was found for both materials, where P is applied pressure and D is the relative density of the porous material.The transient liquid phase formed from the elemental Al and Cu powder particles above the eutectic temperature of 548. °C at low hot pressing pressures, allows to increase the densification due to the reduction in the yield stress of the porous material. The active liquid flow enhanced the deformation between Al particles in the beginning of the pressure ramp.For higher pressures, a sudden break to a higher slope in Konopicky plot was found. This hardening behavior was detected from 610 °C for pure Alumix 13 and it was systematically developed at 580, 600, 610 and 620 °C for the composites, and it can be assigned to diffusion of Cu into the Al grains.During the constant pressure stage the densification was well fitted using the Power Law Creep model with exponents of n = 1 and n = 2, which are related to Newtonian viscous flow and superplastic deformation, respectively. Besides, final hot pressed composites samples retained an important quantity of solidified liquid phase located in between the Saffil fibers agglomerates. © 2013 Elsevier B.V. JOUR info:eu-repo/semantics/openAccess http://creativecommons.org/licenses/by/2.5/ar http://hdl.handle.net/20.500.12110/paper_00325910_v245_n_p13_Moreno |
| institution |
Universidad de Buenos Aires |
| institution_str |
I-28 |
| repository_str |
R-134 |
| collection |
Biblioteca Digital - Facultad de Ciencias Exactas y Naturales (UBA) |
| topic |
Ceramic short fibers Hot pressing Liquid phase sintering Metal matrix composites Power Law Creep Super plastic deformation Hot pressing pressure Hot-pressed composites Metal matrix composites Newtonian viscous flow Power law creep Power-law creep model Short Fiber Transient liquid phase Aluminum Creep Densification Fibers Hot pressing Liquid phase sintering Metallic matrix composites Porous materials Reinforced plastics Liquids aluminum aluminum derivative copper saffil silicon unclassified drug article chemical parameters composite material controlled study deformation density flow Konopicky model liquid phase densification mathematical model physical parameters powder Power Law Creep model pressure solid stress strain relationship temperature viscosity |
| spellingShingle |
Ceramic short fibers Hot pressing Liquid phase sintering Metal matrix composites Power Law Creep Super plastic deformation Hot pressing pressure Hot-pressed composites Metal matrix composites Newtonian viscous flow Power law creep Power-law creep model Short Fiber Transient liquid phase Aluminum Creep Densification Fibers Hot pressing Liquid phase sintering Metallic matrix composites Porous materials Reinforced plastics Liquids aluminum aluminum derivative copper saffil silicon unclassified drug article chemical parameters composite material controlled study deformation density flow Konopicky model liquid phase densification mathematical model physical parameters powder Power Law Creep model pressure solid stress strain relationship temperature viscosity Moreno, M.F. González Oliver, C.J.R. Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing |
| topic_facet |
Ceramic short fibers Hot pressing Liquid phase sintering Metal matrix composites Power Law Creep Super plastic deformation Hot pressing pressure Hot-pressed composites Metal matrix composites Newtonian viscous flow Power law creep Power-law creep model Short Fiber Transient liquid phase Aluminum Creep Densification Fibers Hot pressing Liquid phase sintering Metallic matrix composites Porous materials Reinforced plastics Liquids aluminum aluminum derivative copper saffil silicon unclassified drug article chemical parameters composite material controlled study deformation density flow Konopicky model liquid phase densification mathematical model physical parameters powder Power Law Creep model pressure solid stress strain relationship temperature viscosity |
| description |
The Alumix 13 (wt.%) (Al-4.5 Cu 0.5 Mg 0.2 Si) powder with and without 5 wt.% Saffil short fibers specimens were hot pressed in the range 580-620. °C. The densification during pressure increase was fitted using the Konopicky model and an agreement with the associated linear plot P vs. ln(1/(1 - D) was found for both materials, where P is applied pressure and D is the relative density of the porous material.The transient liquid phase formed from the elemental Al and Cu powder particles above the eutectic temperature of 548. °C at low hot pressing pressures, allows to increase the densification due to the reduction in the yield stress of the porous material. The active liquid flow enhanced the deformation between Al particles in the beginning of the pressure ramp.For higher pressures, a sudden break to a higher slope in Konopicky plot was found. This hardening behavior was detected from 610 °C for pure Alumix 13 and it was systematically developed at 580, 600, 610 and 620 °C for the composites, and it can be assigned to diffusion of Cu into the Al grains.During the constant pressure stage the densification was well fitted using the Power Law Creep model with exponents of n = 1 and n = 2, which are related to Newtonian viscous flow and superplastic deformation, respectively. Besides, final hot pressed composites samples retained an important quantity of solidified liquid phase located in between the Saffil fibers agglomerates. © 2013 Elsevier B.V. |
| format |
JOUR |
| author |
Moreno, M.F. González Oliver, C.J.R. |
| author_facet |
Moreno, M.F. González Oliver, C.J.R. |
| author_sort |
Moreno, M.F. |
| title |
Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing |
| title_short |
Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing |
| title_full |
Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing |
| title_fullStr |
Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing |
| title_full_unstemmed |
Liquid phase densification of Al-4.5wt.% Cu powder reinforced with 5wt.% Saffil short fibers during hot pressing |
| title_sort |
liquid phase densification of al-4.5wt.% cu powder reinforced with 5wt.% saffil short fibers during hot pressing |
| url |
http://hdl.handle.net/20.500.12110/paper_00325910_v245_n_p13_Moreno |
| work_keys_str_mv |
AT morenomf liquidphasedensificationofal45wtcupowderreinforcedwith5wtsaffilshortfibersduringhotpressing AT gonzalezolivercjr liquidphasedensificationofal45wtcupowderreinforcedwith5wtsaffilshortfibersduringhotpressing |
| _version_ |
1807319163011596288 |