Procedure for Modeling a Boost Converter for UPS Using State Variables
This work describes a procedure to model a Boost converter using State Variables. An example will be taken to describe the procedure, a converter used within a UPS that must deliver a constant voltage of 400V to power a bus. The input voltage of this converter is given by a set of batteries that can...
Guardado en:
| Autores principales: | , |
|---|---|
| Formato: | Artículo publishedVersion |
| Lenguaje: | Español |
| Publicado: |
FIUBA
2021
|
| Materias: | |
| Acceso en línea: | https://elektron.fi.uba.ar/elektron/article/view/122 https://repositoriouba.sisbi.uba.ar/gsdl/cgi-bin/library.cgi?a=d&c=elektron&d=122_oai |
| Aporte de: |
| id |
I28-R145-122_oai |
|---|---|
| record_format |
dspace |
| spelling |
I28-R145-122_oai2026-02-11 D'Angiolo, Federico Gabriel Zola, Julio Guillermo 2021-06-15 This work describes a procedure to model a Boost converter using State Variables. An example will be taken to describe the procedure, a converter used within a UPS that must deliver a constant voltage of 400V to power a bus. The input voltage of this converter is given by a set of batteries that can be fully or partially charged, so the input voltage can vary between two possible extreme values. An analysis of the Boost converter circuit will be carried out as an introduction to later carry out the corresponding modeling. This modeling will allow to analyze its stability, the variations in the output voltage in the face of changes in the input, as well as the different disturbances that may occur. En el presente trabajo se describe un procedimiento para el modelado de un convertidor Boost utilizando variables de estado. Se tomará como ejemplo para describir el procedimiento, un convertidor utilizado en el interior de una UPS que debe entregar una tensión constante de 400V para alimentar a un bus. La tensión de entrada de este convertidor viene dada por un conjunto de baterías las que pueden estar totalmente o parcialmente cargadas, razón por la cual la tensión de entrada puede variar entre dos posibles valores extremos. Se realizará como introducción un análisis del circuito convertidor Boost para luego realizar la modelización correspondiente. Esta modelización permitirápoder analizar su estabilidad, las variaciones de la tensión de salida frente a cambios en la entrada, así como las distintas perturbaciones que pudieran ocurrir. application/pdf text/html https://elektron.fi.uba.ar/elektron/article/view/122 10.37537/rev.elektron.5.1.122.2021 spa FIUBA https://elektron.fi.uba.ar/elektron/article/view/122/236 https://elektron.fi.uba.ar/elektron/article/view/122/237 Derechos de autor 2021 Federico Gabriel D'Angiolo, Julio Guillermo Zola Elektron Journal; Vol. 5 No. 1 (2021); 1-6 Revista Elektron; Vol. 5 Núm. 1 (2021); 1-6 Revista Elektron; v. 5 n. 1 (2021); 1-6 2525-0159 2525-0159 modelling switching converter state variables modelización convertidor variables de estado Procedure for Modeling a Boost Converter for UPS Using State Variables Procedimiento para el modelado de un convertidor boost para UPS mediante variables de estado info:eu-repo/semantics/article info:eu-repo/semantics/publishedVersion https://repositoriouba.sisbi.uba.ar/gsdl/cgi-bin/library.cgi?a=d&c=elektron&d=122_oai |
| institution |
Universidad de Buenos Aires |
| institution_str |
I-28 |
| repository_str |
R-145 |
| collection |
Repositorio Digital de la Universidad de Buenos Aires (UBA) |
| language |
Español |
| orig_language_str_mv |
spa |
| topic |
modelling switching converter state variables modelización convertidor variables de estado |
| spellingShingle |
modelling switching converter state variables modelización convertidor variables de estado D'Angiolo, Federico Gabriel Zola, Julio Guillermo Procedure for Modeling a Boost Converter for UPS Using State Variables |
| topic_facet |
modelling switching converter state variables modelización convertidor variables de estado |
| description |
This work describes a procedure to model a Boost converter using State Variables. An example will be taken to describe the procedure, a converter used within a UPS that must deliver a constant voltage of 400V to power a bus. The input voltage of this converter is given by a set of batteries that can be fully or partially charged, so the input voltage can vary between two possible extreme values. An analysis of the Boost converter circuit will be carried out as an introduction to later carry out the corresponding modeling. This modeling will allow to analyze its stability, the variations in the output voltage in the face of changes in the input, as well as the different disturbances that may occur. |
| format |
Artículo publishedVersion |
| author |
D'Angiolo, Federico Gabriel Zola, Julio Guillermo |
| author_facet |
D'Angiolo, Federico Gabriel Zola, Julio Guillermo |
| author_sort |
D'Angiolo, Federico Gabriel |
| title |
Procedure for Modeling a Boost Converter for UPS Using State Variables |
| title_short |
Procedure for Modeling a Boost Converter for UPS Using State Variables |
| title_full |
Procedure for Modeling a Boost Converter for UPS Using State Variables |
| title_fullStr |
Procedure for Modeling a Boost Converter for UPS Using State Variables |
| title_full_unstemmed |
Procedure for Modeling a Boost Converter for UPS Using State Variables |
| title_sort |
procedure for modeling a boost converter for ups using state variables |
| publisher |
FIUBA |
| publishDate |
2021 |
| url |
https://elektron.fi.uba.ar/elektron/article/view/122 https://repositoriouba.sisbi.uba.ar/gsdl/cgi-bin/library.cgi?a=d&c=elektron&d=122_oai |
| work_keys_str_mv |
AT dangiolofedericogabriel procedureformodelingaboostconverterforupsusingstatevariables AT zolajulioguillermo procedureformodelingaboostconverterforupsusingstatevariables AT dangiolofedericogabriel procedimientoparaelmodeladodeunconvertidorboostparaupsmediantevariablesdeestado AT zolajulioguillermo procedimientoparaelmodeladodeunconvertidorboostparaupsmediantevariablesdeestado |
| _version_ |
1859522224874061824 |